FIELD CONTROLS Hardware platform 10 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Sítě FIELD CONTROLS Hardware platform 10. FIELD CONTROLS Hardware platform 10 User's Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 22
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Installation Guide
Hardware Platform 10
FChwp10
Zobrazit stránku 0
1 2 3 4 5 6 ... 21 22

Shrnutí obsahu

Strany 1

Installation GuideHardware Platform 10FChwp10

Strany 2

Hardware Platform 10 Installation Guide10(ELS1700 or EWS1700 only) VGA Audio USB(ELS172

Strany 3

InstallationCER International bv 11Hardware installationYou communicate with the controller over the Ethernet network. In this part of thechapter,

Strany 4

Hardware Platform 10 Installation Guide12Power Over EthernetIn your controller a passive power over Ethernet (PoE) scheme is implemented (seebelow), u

Strany 5

InstallationCER International bv 13Connecting to the networkBefore connecting the controller to the network, you might want to consult your networ

Strany 6

Hardware Platform 10 Installation Guide14To connect the CER controller to your 10/100base-T network, you can use any standardCategory 5 (CAT5). A suit

Strany 7

IP configurationCER International bv 15IP configurationYour CER controller uses the common TCP/IP protocols to provide the connection to theclient

Strany 8

Hardware Platform 10 Installation Guide16For FieldCommander controllers:Assigning an IP address on a FieldCommanderThe factory default IP address of

Strany 9

IP configurationCER International bv 17Note: For security reasons, it is strongly recommended to change this password. See the User's Guide

Strany 10

Hardware Platform 10 Installation Guide18Caution: Be aware that, when your FieldCommander is assigned a dynamicaddress, you may not know which address

Strany 11

IP configurationCER International bv 19Force new IP address using ARP+PINGWhen FieldCommander is outside of your subnet or or you don't recal

Strany 13

Hardware Platform 10 Installation Guide20For ELS controllers:Assigning an IP address on an ELS controllerThe IP address on an ELS controller is defin

Strany 14

IP configurationCER International bv 21For EWS controllers:Assigning an IP address on an EWS controllerThe IP address on an EWS controller is def

Strany 15

Hardware Platform 10 Installation Guide22Testing the Ethernet connectionThe ping testThe most basic way to test the network connection is to do a so-c

Strany 17

Safety InformationThe following are warnings or safety guidelines. A warning means danger. You are in asituation that could cause bodily injury. Befor

Strany 18

Restricted Access Area Warning The device is intended for installation in restricted access areas. A restricted access area is an areato which access

Strany 19

Power Supply Disconnection Warning Before working on the device or near power supplies, disconnect the power. Waarschuwing Voordat u aan een frame of

Strany 20

Hardware Platform 10 Installation Guide6Table of ContentsSafety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Strany 21

About this manualCER International bv 7About this manualThis document is intended for users of the FieldCommander, ELS- or EWS controllers thatare

Strany 22

Hardware Platform 10 Installation Guide8InstallationThis chapter explains the installation in detail and along the way it introduces you tosome of the

Strany 23

InstallationCER International bv 9LED indicatorNext to the Power Connector there is a green LED on the front panel for indicating systemstatus. Th

Komentáře k této Příručce

Žádné komentáře